mmWave SDK demo中集成I2C接口驱动所需的步骤及操作

mmWave SDK demo中集成I2C接口驱动所需的步骤及操作

本文的测试环境如下：

测试软件版本：mmWave SDK 2.0.0.4

测试硬件：AWR1642BOOST EVM

1. 在mmWave SDK demo中增加I2C驱动代码

注意LP87524B寄存器信息来源于其datasheet：LP87524B/J-Q1具有集成开关的具有集成开关的 4-A + 2.5-A +两个 1.5-A降压稳压器数据表 (Rev. A)，I2C驱动参考代码如下：

#include

static int32_t I2C_GPIOInit(void)

{

#if (defined(SOC_XWR14XX))

Pinmux_Set_FuncSel(SOC_XWR14XX_PINR3_PADAH, SOC_XWR14XX_PINR3_PADAH_I2C_SDA);

Pinmux_Set_OverrideCtrl(SOC_XWR14XX_PINP4_PADAI, PINMUX_OUTEN_RETAIN_HW_CTRL, PINMUX_INPEN_RETAIN_HW_CTRL);

Pinmux_Set_FuncSel(SOC_XWR14XX_PINP4_PADAI, SOC_XWR14XX_PINP4_PADAI_I2C_SCL);

#else

/* Setup the PINMUX to bring out the XWR16xx I2C pins */

Pinmux_Set_OverrideCtrl(SOC_XWR16XX_PINF13_PADAH, PINMUX_OUTEN_RETAIN_HW_CTRL, PINMUX_INPEN_RETAIN_HW_CTRL);

Pinmux_Set_FuncSel(SOC_XWR16XX_PINF13_PADAH, SOC_XWR16XX_PINF13_PADAH_I2C_SDA);

Pinmux_Set_OverrideCtrl(SOC_XWR16XX_PING14_PADAI, PINMUX_OUTEN_RETAIN_HW_CTRL, PINMUX_INPEN_RETAIN_HW_CTRL);

Pinmux_Set_FuncSel(SOC_XWR16XX_PING14_PADAI, SOC_XWR16XX_PING14_PADAI_I2C_SCL);

#endif

return 0;

}

static int32_t I2C_Communication_Test()

{

bool retVal = false;

int32_t errCode = 0;

uint32_t arg;

uint8_t rxData[16];

uint8_t txData[16];

I2C_Transaction i2cTransaction;

I2C_Handle i2cHandle;

/* Reset the transmit and receive buffer */

/* Initializa the I2C driver */

I2C_init();

I2C_Params_init(&i2cParams);

i2cParams.transferMode = I2C_MODE_BLOCKING;

i2cParams.bitRate = I2C_100kHz;

/* Open the I2C driver */

i2cHandle = I2C_open(0, &i2cParams);

if (i2cHandle == NULL)

{

System_printf ("Error: I2C Driver Open failed\n");

return -1;

}

arg = 0;//arg set to 0, and the I2C addr mode is 7-bit.

errCode = I2C_control (i2cHandle, I2C_CMD_ADDR_MODE, (void* )&arg);

if (errCode < 0)

{

System_printf ("Error: I2C control Set I2C_CMD_ADDR_MODE failed [Error code %d]\n", errCode);

return -1;

}

//read the LP87524B buck3 output voltage register

txData[0] = 0x10;

i2cTransaction.slaveAddress = 0x60;//LP87524B/J-Q1 Device Address = 0x60

i2cTransaction.writeBuf = txData;

i2cTransaction.writeCount = 1;

i2cTransaction.readBuf = rxData;

retVal = I2C_transfer(i2cHandle, &i2cTransaction);

if (retVal == false)

{

System_printf ("Error: I2C Transfer failed\n");

return -1;

}

System_printf("I2C_READ: addr=0x%x, Val=0x%x\n",txData[0],rxData[0]);

//write the LP87524B buck3 output voltage = 2.0V

txData[0] = 0x10;

txData[1] = 0xbb;//default=0xca,2.3V,0xb1=1.8V, 0xbb=2.0V

i2cTransaction.slaveAddress = 0x60;//LP87524B/J-Q1 Device Address = 0x60

i2cTransaction.writeBuf = txData;

i2cTransaction.writeCount = 2;

i2cTransaction.readBuf = rxData;

i2cTransaction.readCount = 0;

retVal = I2C_transfer(i2cHandle, &i2cTransaction);

if (retVal == false)

{

System_printf ("Error: I2C Transfer failed\n");

return -1;

}

System_printf("I2C_Write: LP87524B buck3 = 2.0V Done\n");

//read the LP87524B buck3 output voltage register

txData[0] = 0x10;

i2cTransaction.slaveAddress = 0x60;//LP87524B/J-Q1 Device Address = 0x60

i2cTransaction.writeBuf = txData;

i2cTransaction.writeCount = 1;

i2cTransaction.readBuf = rxData;

i2cTransaction.readCount = 1;

retVal = I2C_transfer(i2cHandle, &i2cTransaction);

if (retVal == false)

{

System_printf ("Error: I2C Transfer failed\n");

return -1;

}

System_printf("I2C_READ: addr=0x%x, Val=0x%x\r\n",txData[0],rxData[0]);

//write the LP87524B buck2 output voltage = 1.5V

txData[0] = 0x0e;

txData[1] = 0Xa2;//default=0xb1,1.8V, 0x4d=1V 0xa2=1.5V

i2cTransaction.slaveAddress = 0x60;//LP87524B/J-Q1 Device Address = 0x60

i2cTransaction.writeBuf = txData;

i2cTransaction.writeCount = 2;

i2cTransaction.readBuf = rxData;

i2cTransaction.readCount = 0;

retVal = I2C_transfer(i2cHandle, &i2cTransaction);

if (retVal == false)

{

System_printf ("Error: I2C Transfer failed\n");

return -1;

}

System_printf("I2C_Write: LP87524B buck2 = 1.5V Done\n");

if (retVal == false)

{

System_printf ("Error: I2C combined Transfer to Slave failed\n");

return -1;

}

/* Close I2C driver */

I2C_close(i2cHandle);

return 0;

}

//Call these function in void MmwDemo_mssInitTask(UArg arg0, UArg arg1)

errCode = I2C_GPIOInit();

if (errCode == -1)

System_printf("I2C_GPIOInit Error\r\n");

errCode = I2C_Communication_Test();

if (errCode == -1)

System_printf("I2C_Communication_Test Error\n");

else

System_printf("I2C_Communication_Test Done\n");

2. 将工程链接到I2C驱动库

最后一步是通过链接I2C驱动程序来构建可执行文件。 如果使用CCS项目，可以将I2C驱动程序添加到项目的链接器属性中，如图1所示。

图1. CCS Project Linker Properties

如果使用makefile编译工程，执行相同的程序。

###################################################################################

# Additional libraries which are required to build the DEMO:

###################################################################################

MSS_MMW_DEMO_STD_LIBS = $(R4F_COMMON_STD_LIB) \

-llibpinmux_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibdma_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibcrc_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibgpio_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibmailbox_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibmmwavelink_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibmmwave_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibcli_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT) \

-llibi2c_$(MMWAVE_SDK_DEVICE_TYPE).$(R4F_LIB_EXT)

MSS_MMW_DEMO_LOC_LIBS = $(R4F_COMMON_LOC_LIB) \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/drivers/pinmux/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/drivers/uart/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/drivers/crc/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/drivers/gpio/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/drivers/mailbox/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/control/mmwavelink/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/control/mmwave/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/utils/cli/lib \

-i$(MMWAVE_SDK_INSTALL_PATH)/ti/utils/i2c/lib

3. 运行测试例程

**********************************************

Debug: Launching the Millimeter Wave Demo

**********************************************

I2C_READ: addr=0x10, Val=0xca

I2C_Write: LP87524B buck3 = 2.0V Done

I2C_READ: addr=0x10, Val=0xbb

I2C_Write: LP87524B buck2 = 1.5V Done

I2C_Communication_Test Done

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。